OzBuyz Store · Australia
Tools and Workshop Equipment Australia
Browse power tools, hand tools, workshop equipment, measuring products, storage and accessories for trade, maintenance and DIY tasks. Compare power source, voltage, capacity, speed or torque range, compatible accessories, duty... Read moreShow less
Last reviewed 2 August 2026 by the Ozbuyz Store Editorial Team.
Tools and workshop equipment selected as complete working systems
Choose equipment from the material, task, environment and consequence of failure rather than one maximum power or capacity figure. The verified Ozbuyz range includes air compressors and pneumatic accessories, industrial tools, hand tools and accessories, power tools, pumps and tool storage and workbenches.
| Tool area | Typical products | What to confirm first |
|---|---|---|
| Compressed Air | Compressors, tanks, hoses, regulators, filters, fittings and pneumatic accessories | Free-air delivery at working pressure, tank, duty cycle, tool demand, hose bore, connector and pressure rating |
| Power Tools | Drills, saws, sanders, chainsaws, generators, nailers, jackhammers, painting and welding equipment | Australian electrical supply, battery platform, speed, accessory interface, guards, dust or fume control and operating area |
| Industrial Tools | Ladders, scaffolding, hoists, measuring tools, heat guns, traffic products and protective equipment | Work method, duty rating, working load limit, height, support, calibration, environment and workplace requirements |
| Hand Tools & Accessories | Hand tools, sockets, drill bits, blades, clamps, vices, sanding products and electrical supplies | Drive, shank, bore, diameter, material, maximum speed, impact rating, insulation claim and work holding |
| Pumps | Air, irrigation, pool, drainage and sewage pumps | Required flow at total head, liquid and solids, duty, dry-run protection, electrical supply and discharge size |
| Storage & Benches | Toolboxes, cabinets, trolleys, wall racks and workbenches | Load per drawer or shelf, total load, castors and brakes, anchoring, worktop and assembly |
Match every tool to its accessory and power system
Confirm the battery platform, charger, plug, current, chuck or shank, blade diameter, bore, speed rating, hose, fitting and pressure before combining products. A component fitting physically does not prove that its load, speed, chemistry, electrical communication or intended use is compatible. Impact tools require impact-rated accessories, and cutting tools must retain the specified guards.
Use operating performance rather than isolated maximum figures
For compressors, use free-air delivery at the pneumatic tool’s working pressure and include duty cycle and hose losses. For pumps, use the required flow at total dynamic head and confirm the liquid, solids and duty. For generators, calculate simultaneous continuous load and motor startup demand. For welding equipment, compare duty cycle at the required current and the input circuit.
Control dust, fumes, noise, height and stored energy
Silica, wood dust and welding fumes should be controlled at source through suitable wet methods, guarding, on-tool extraction or local exhaust ventilation before relying on personal protective equipment. Select respiratory, eye, hearing, hand and body protection for the exact hazard. Keep generators and outdoor fuel equipment outside enclosed areas, isolate electrical or pneumatic energy before maintenance and keep people clear of suspended loads.
Check Australian compliance and licensed work
In-scope electrical equipment should have the applicable Australian responsible supplier, registration and Regulatory Compliance Mark. A foreign approval logo or plug adapter is not an equivalent Australian supply check. Fixed wiring, generator changeover systems, three-phase or high-current outlets and many pump or workshop installations require licensed work. Workplace users also have WHS duties beyond the product purchase.
Read the complete Australian tools guide
The Tools and Workshop Equipment Buying Guide for Australia covers electrical and battery compatibility, drills, blades, silica control, PPE, chainsaws, compressors, generators, ladders, hoists, welding, pumps, storage, inspection and consumer rights.
The catalogue is actively updated and several tool leaves contain automotive, workshop or unrelated products. Confirm the individual listing’s exact product type, specifications, inclusions and intended use before ordering.
Australia-wideDelivery options shown at checkout
Secure checkoutProtected online payments
14-day returnsOn eligible change-of-mind items
Explore6subcollections
Shop withconfidenceAustralian support
Step 2 of the collection path
Choose a subcollection
Select a category inside Tools to continue to a more specific range.
Helpful answers
Frequently asked questions about Tools
Why is free-air delivery more useful than compressor displacement when choosing an air compressor?
Displacement is a theoretical intake figure based on pump geometry, while free-air delivery estimates the usable air delivered after real pump losses. Compare FAD at the pneumatic tool's required pressure, not only a maximum litre-per-minute figure with no pressure stated. The compressor should cover the tool's average and peak demand with a margin for hose loss and leaks. A larger receiver stores more air and reduces cycling but does not increase the pump's sustainable production.
How do I match a pneumatic tool's air demand to a compressor and duty cycle?
Find the tool's required airflow at its stated working pressure and decide whether the use is intermittent or continuous. Nailing can rely more on receiver storage, while sanding, spraying and blasting require sustained output. Compare the compressor's FAD and permitted duty cycle, then account for simultaneous tools, leakage and pressure drop. If demand exceeds supply, pressure will fall and the compressor can run continuously or overheat even when the tank and maximum-pressure figures appear adequate.
Which hose and fitting specifications matter in a compressed-air system?
Check hose internal diameter, length, working-pressure rating, temperature and material, plus the exact coupling profile and thread. A long narrow hose can starve a high-flow tool even while tank pressure remains high. Every regulator, filter, connector and accessory must be rated above the system's maximum pressure. Secure hoses against whipping, protect them from vehicles and sharp edges and isolate and depressurise the system before disconnecting or servicing it.
What do chain pitch, gauge and drive-link count mean when replacing a chainsaw chain?
Pitch describes spacing within the chain drive system, gauge is the thickness of the drive links that run in the guide-bar groove, and drive-link count determines the chain's total loop length for that bar and sprocket combination. All three must match the saw, bar and drive sprocket. Bar length alone is insufficient. Install the chain in the correct direction, set tension as instructed and confirm free movement, lubrication and chain-brake operation before cutting.
How do I match a saw blade or cutting disc by diameter, bore, speed and material?
Use only a blade or disc approved for the tool type. Match outside diameter, bore or arbor, flange arrangement and direction, and ensure the accessory's maximum RPM is at least the tool's no-load speed. Then select tooth, grit or abrasive specification for the workpiece material and thickness. Never fit a larger accessory by removing a guard or use an improvised reducer. Inspect for cracks, distortion, missing teeth and expiry where applicable before installation.
View 10 more questions
When must a socket, bit or accessory be impact rated?
Use an impact-rated accessory whenever it will receive repeated blows from an impact driver, impact wrench or another percussive drive system. Ordinary hand sockets and non-impact holders can be too brittle and may crack or fragment. Match the drive size, fastener, shank and tool torque and inspect for wear. An impact tool's numbered setting is not a calibrated final torque, so use the specified tightening method and a suitable torque wrench where a critical fastener requires a measured value.
Why is an Australian Regulatory Compliance Mark different from a foreign approval logo?
The RCM links applicable electrical equipment to an Australian responsible supplier and the required electrical-safety and electromagnetic-compliance framework. A CE mark, overseas laboratory certificate, foreign plug or travel adapter does not establish that the product has followed Australia's supplier, registration and marking process. Also confirm the Australian plug, voltage, frequency and current. Compliance marking addresses supply obligations but does not prove that the workshop circuit, accessory or use method is suitable.
Can a portable generator be connected to a building through a wall socket or homemade lead?
No. Backfeeding through a wall socket can energise building and network wiring and electrocute occupants, neighbours or electricity workers. Operate the generator outdoors with exhaust away from openings and use only the outlets and leads permitted by its instructions. A dedicated building inlet, transfer or changeover system must be designed and installed by a licensed electrician. The generator also needs protection from weather without being enclosed and must cool before refuelling.
How do total head and flow work together when selecting a water pump?
Maximum flow is normally measured at little or no head, while maximum head occurs near zero flow. Calculate total dynamic head from vertical lift, required outlet pressure and friction through pipe, hose, valves and fittings, then read the pump curve to find the flow available at that head. Confirm suction conditions, priming, duty cycle and inlet or outlet sizes. Choosing independently from either maximum number can result in inadequate flow or an unsuitable operating point.
Can a sewage or dirty-water pump pass any material smaller than its stated solids size?
No. The solids figure describes a permitted size under stated conditions, not every shape or material. Wipes, cloth, string, hair, fibrous waste, stones and long objects can wrap, bridge or jam a pump even when one dimension is smaller than the opening. Check whether the design is vortex, cutter or grinder type and what liquids and solids are expressly permitted. Provide float-switch clearance and never enter a pit or tank without legally required confined-space controls.
How do I choose a ladder's duty rating and set it up correctly?
Select a ladder type and length that allow the task without standing above the permitted step or overreaching. The load includes the user, clothing, tools and materials. Workplace guidance commonly requires an industrial ladder with at least a 120-kilogram rating. Inspect stiles, rungs, feet, locks and labels, use a firm level surface and keep three points of contact. Fully open a stepladder; for straight or extension ladders, follow the specified securing and approximately 4:1 setup guidance.
What does working load limit mean for a hoist, sling and anchor system?
WLL is the maximum permitted load for a component under its stated configuration and conditions. The complete lifting system is limited by the lowest-rated hoist, chain, rope, hook, shackle, sling, trolley, beam clamp, anchor or supporting structure after accounting for sling angle, side loading, shock and environment. Equipment designed only for pulling must not be used for vertical lifting, and non-personnel equipment must never lift people. Keep everyone outside the fall zone and never work beneath a load supported only by a hoist.
How do welding duty cycle and input current affect machine selection?
Duty cycle states how long the welder can operate at a specified output current and ambient condition within a standard period before cooling. A high maximum-amp headline can therefore represent only short operation. Select the machine from the current required for the material and process, then check duty cycle at that output. Also verify input current, plug and circuit; a 15-amp or three-phase machine cannot be safely adapted to an ordinary 10-amp outlet. Licensed electrical work may be required.
Why does a disposable dust mask not automatically protect against silica or welding fume?
Respiratory hazards differ in particle size, concentration and whether gases or vapours are present. Protection requires a suitable respirator and filter class, correct facial fit, fit testing where required and a clean sealing area for tight-fitting designs. Respirators are used after higher-order controls such as wet cutting, on-tool extraction or local exhaust ventilation. A simple nuisance-dust mask can be inadequate for respirable crystalline silica, welding fume or chemical vapours and should not be selected from appearance alone.
How should a workbench, wall rack or mobile tool cabinet be loaded and secured?
Check separate limits for the worktop, each shelf or drawer and the complete unit. Store heavy items low, distribute loads and avoid opening several loaded drawers unless the design permits it. Wall systems need fixings suited to the structural substrate and the cantilevered tool load; decorative plasterboard or an unknown adhesive is not sufficient for heavy equipment. Lock mobile castors before work and anchor benches or cabinets where the instructions or applied forces require it.